MAXDATA QutePC?1000 Guía de usuario Pagina 113
- Pagina / 163
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
112 Configuration Software and Utilities
113MAXDATA PLATINUM 90002R Server System
Console Conguration
1. Boot the console into the operating system.
2. Launch HyperTerminal by clicking the Start button in the task bar.
3. Select Programs>Accessories>Communications and click HyperTerminal.
4. At the Connection Description window, enter guest for the name and click OK.
5. At the Connect To window, select the COM port of the console that the null modem is
connected. In this example, it is COM1.
6. At the COM1 Properties window, select 19200 for the Bits per second (Baud rate) box to the
SMU conguration on the server.
7. Select None for the Flow Control to match the BMC conguration.
8. Leave the default settings for the other boxes. Click OK to accept the settings and enter the
HyperTerminal screen.
9. The PING message sent by the BMC is displayed as characters on the HyperTerminal screen.
10. Press the <ESC> key followed by <(> to enable Terminal Mode and end the PING messages.
[TMODE OK] is displayed.
11. Type [SYS TMODE], it is case sensitive and must be in uppercase. The response is [OK TMODE]
indicating that Terminal Mode is functioning.
Logging Into the Terminal Mode Session
Reminder: Guest was the password set for the Anonymous User in the BMC.
1. At the HyperTerminal screen enter [SYS PWD –N guest] to login. -N represents the Anonymous
User; guest is the password. This text is case sensitive.
2. The screen returns [SYS] and [OK] to indicate a successful login.
3. Type any supported terminal mode command.
4. To logout type [SYS PWD –X]
User Conguration
A user must be congured through the SMU to make full use of terminal mode. To create a user,
navigate to the SMU user conguration screen. Enter any username and password combinations
desired. Make sure to check the box that enables a particular user for use on the serial channel. If
this is not done, the username is not useable on the serial channel for terminal mode. Congure the
user with the desired maximum privilege level. See User Conguration Sub-task for details about
the user conguration screens.
Spaces, left bracket characters or right bracket characters are not allowed in usernames or passwords
used with terminal mode.
Security Information
Terminal mode access to the BMC is governed by the user name and password conguration through
the SMU; before the server will accept terminal mode commands, a session must be established.
However, a limited selection of text commands and binary hex-ASCII commands that are assigned
the lowest IPMI privilege level are available before session establishment with the BMC.
Since the terminal mode password is sent via clear text, the terminal mode session should take place
in a secure location over a secure link, preferably via a direct connection. Connection via a modem is
supported but not recommended.
- Product Guide 1
- Contents 3
- 4 Contents 4
- 6 Contents 6
- 4 Technical Reference 125 8
- Safety Warnings 153 8
- 8 Contents 9
- Important Safety Information 11
- Conventions 12
- 1 System Description 13
- External Chassis Features 15
- Front Panel 16
- Peripheral Bay 17
- Hot-swap Hard Drive Carrier 18
- Removable Media Drive Bay 19
- CAUTION 19
- Power Supply Bay 20
- • AC input #1 available 21
- • AC input #2 available 21
- • TS-OK signal is asserted 21
- Chassis Rear 22
- Internal Chassis Features 23
- Cooling Subsystem 25
- CAUTIONS 25
- 26 System Description 26
- NOTES 27
- Processor Power Pods 28
- 2 Board Set Description 29
- 30 Board Set Description 30
- Main Board 31
- Processor Sockets 33
- Memory Subsystem 33
- SCSI Controller 34
- Network Interface Controller 34
- Video Controller 34
- IDE Controller 35
- PCI Riser Board 36
- SCSI Backplane Board 37
- Front Panel Board 39
- Size] 46
- CMOS Clear 47
- WARNING 47
- BIOS Recovery Mode 48
- BIOS Setup 49
- Setup Screens 50
- Advanced 51
- Security 52
- System Management 52
- LSI Logic SCSI Utility 55
- System Maintenance Utility 57
- Remote Keyboard Navigation 58
- Local Keyboard Navigation 58
- About Box Information 59
- Server Discovery 60
- Remote SMU Application 60
- Running from CD 62
- Local SMU Application 62
- Shutdown SMU Application 63
- Access Mode 65
- Privilege Level Limit 65
- Enable DHCP 65
- LAN Alert Conguration 67
- Enable LAN Alerting 67
- SNMP Community String 67
- Alert Settings 68
- New, Edit, and Delete Buttons 68
- New/Edit LAN Alert 68
- User Conguration Sub-task 71
- Enable User 72
- Enter Username 72
- Clear Password 72
- Enter/Verify New Password 72
- Edit Event Filter Settings 75
- Enable Event Filter 75
- Enable Alerts 76
- Congure Policies Button 76
- Alert Policy Table 76
- Edit Alert Policy Entry 78
- Enable Policy Entry 78
- Policy Number 78
- Policy Type 78
- Select the Destination 79
- Connection Mode 80
- Modem Mode Conguration 81
- Modem Init String 81
- Modem Escape Sequence 82
- Hang-up Sequence 82
- Dial Command 82
- Ring Duration 82
- Ring Dead Time 82
- Destination Dial Strings 83
- New/Edit Dial String 84
- Destination Dial String 84
- Page Destination Conguration 85
- Enable Paging 85
- Data Bits 87
- Call Retries 87
- Terminal Mode Conguration 87
- Enable Terminal Mode 87
- Power Conguration Sub-task 89
- SEL Viewer 90
- Viewing Events in the SEL 91
- Save Log Button 93
- Open Log Button 93
- Clear SEL Button 93
- Properties Button 93
- Reload Button 93
- Display as Hex Button 94
- Display as Text Button 94
- SDR Viewer 94
- Viewing SDRs 95
- Viewing FRUs 97
- Save To File Button 98
- Open File Button 98
- ISM Front-end Help 100
- SMU Table of Contents Help 100
- EFI Platform Diagnostic Tests 102
- EFI Service Partition 104
- Installing the Files 105
- Console Redirection 106
- Keystroke Mappings 107
- (xxh) = ASCII character xx 108
- NS = not supported 108
- NS = Not supported 108
- Limitations 109
- Server Management Interface 109
- Server Conguration 109
- Terminal Mode 110
- Hardware Setup 111
- Serial Channel Conguration 111
- Console Conguration 113
- User Conguration 113
- Security Information 113
- Hex-ASCII Command Format 115
- Text Command Format 115
- Examples 115
- Shutting Down the Server 123
- 4 Technical Reference 125
- System Interconnection 126
- User-Accessible Interconnects 127
- Video Port 128
- Ethernet Connector 129
- Ultra320 SCA-2 HDD Connector 131
- Jumper Information 133
- Conguring Main Board Jumpers 134
- POST Error Codes and Messages 135
- Specic POST Code Modules 138
- SAL-A Module 138
- SAL-B Module 140
- SAL-F Module 143
- IA-32 Module 144
- Recovery Port 80 Codes 148
- POST Beep Codes 150
- Memory Test Failure 151
- Safety Warnings 153
- WARNING: English (US) 154
- AVERTISSEMENT: Français 156
- WARNUNG: Deutsch 158
- AVVERTENZA: Italiano 160
- ADVERTENCIAS: Español 162
Relacionado con productos y manuales para Servidores MAXDATA QutePC?1000
(47 paginas)
Servidores MAXDATA PLATINUM 520 Manual de usuario
(31 paginas)
(31 paginas)
Servidores MAXDATA PLATINUM 110 Manual de usuario
(31 paginas)
(31 paginas)
(23 paginas)
Servidores MAXDATA PLATINUM 220 Manual de usuario
(31 paginas)
(31 paginas)
Servidores MAXDATA PLATINUM 100 I Manual de usuario
(29 paginas)
(29 paginas)
Servidores MAXDATA PLATINUM 510 Manual de usuario
(52 paginas)
(52 paginas)
(6 paginas)
Servidores MAXDATA SR1202 M1 Guía de usuario
(152 paginas)
(152 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.040 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales